Click here for more on TONE Electric Torque Control Wrench. The HYTORC Washer is manufactured in accordance with the requirements in the ASTM F3394F3394M Standard Specification for Hardened Steel Backup and Reaction Washers.
The further away the force from the torque is applied the smaller the magnitude of the force.
Torque washer. The range is constantly growing with the backing of world class. This standard covers general-purpose mechanical and structural use of washers with bolts nuts studs Direct Tension Indicators and other threaded fasteners. Four bent prongs on the washer can be embedded in wood plywood and other ductile materials making the washer self-retaining during assembly.
When performing an oil change it is always recommended to change your sump plug and washer to ensure adequate sealing. The same can be achieved by using a KEPS unit a washer being held captive on a nut. Load Indicating Washers DTI F959 Load indicating washers LIW are used to develop the correct tension when installing A325 or A490 structural bolts.
247 Support Click here for 247 customer service in 30 minutes or less. Other Notes Required Fields. Theyre zinc-plated steel for corrosion resistance in wet environments.
Standard DTIs and Squirter DTIs are made to. Or call us today at 1-866-895. Once it is installed along the nut.
Click here for more on Squirter DTI Washers. Ring terminals have been in use for 100 years and SAE J1908 Electrical. They have a tooth that sits down in the dropout and helps apply the torque of the motor further from the center of the axle.
Load Indicator Washer ASTM F959M. Available for different bolt grades and dimensions. Torque Washers are formed with sharp prongs to sink into the mating surface.
With flat washer and split ring approach higher torque can be applied and a gas tight seal is made such that oxygen can not start corrosion. Click here to Request a Quote. The finished square hole in the washer mates with the square shoulder on the carriage.
The square-holed washer is designed for use with a carriage bolt. About Nord-Lock Products Go back Original Washers X-series Washers Steel Construction Washers Wheel Nuts Combi Bolt Washers Customized Solutions. Torque washers are used either in addition to or in place of torque arms.
It is good practice to specify which part should be tightened so that the bolt preload variation is minimised. Click here for more on Class 88 AS1252 Structural Bolts. Company Phone Email.
So in general when using torque control tightening the bolt by rotating the bolt head or the nut can matter. Torque Washer Contact Form. Pro-Torque offers a complete range of engine components covering 95 of the Australian car parc with everything you need to do the job.
Minimum torque if scatter is 23 1602 x 077 1234 Nm Torque should be set to 1602 Nm mean torque on the torque wrench The accuracy of the tightening method as well as the change in friction needs to be accounted for in order not to over-tighten the fastener. Torque washer has inner surface in quare shape. Squirter DTI Direct Tension Indicator Washer ASTM F959M.
A torque washer is a type of washer designed for use in a soft penetrable material in which a bolt would probably not be able to stay fastened tightly inside. While it has three or four locking structures along the surface. For technical drawings and 3-D models click on a part number.
Designed for use with square-neck bolts such as carriage bolts these washers have teeth that dig into wood and other soft material to prevent rotation. For instance bolts can come loose in soft woods over time especially if the surrounding environment is prone to cause significant warping variable in temperature or if the wood or bolt itself carry a variable load. Torque values to install Nord-Lock washers.
Concrete panel Washer AS12371-2002 Table 3 Structural Washers AS1252. The HYTORC VECTOR Torque Angle Pump is the worlds leading fully-automatic hydraulic power pack for. 19 rows It correctly indicates bolt tension and is not affected by poor torque tension correlation.
A complete line of unique square-holed Torque Washers is now available from WCL Company. Sump plugs washers are an integral part of any vehicle sealing in the critical engine oil sealing leaks and preventing contaminants from infiltrating your engine. Pro-torque is a trusted Australian company employing Australian people which allows Pro-Torque to be distributed through an advanced interlinked warehouse and distributor network.
With serrated nuts or star washers lower torque leads to more open circuits and some sort of liquid tape is needed to seal the moisture out which assembly and service people hate. The HYTORC Washer system includes the HYTORC Reaction Washer Backup Washer and the locking J-Washer. Product Contact Form Click To Toggle Product Contact Info Name.
These washers are used where non-rotation between the washer and surface is required. Its locking structures gives resistance to loosening from wooden or rubber structures.